* User Info

Welcome, Guest. Please login or register.

* Who's Online

  • Dot Guests: 21
  • Dot Hidden: 0
  • Dot Users: 0

There aren't any users online.

* Recent Topics

For Sale - One Piece Fiberglass Rear Door for CF Van by Rotti
[November 24, 2021, 12:42:56 AM]

Ballast Resistor by pickmeup
[October 19, 2021, 04:25:04 AM]

Door hinge check spring. by wendyh
[October 01, 2021, 10:21:08 PM]

Daily Post by wendyh
[August 31, 2021, 10:28:00 PM]

I am Back!! by wendyh
[June 30, 2021, 08:11:11 AM]

Looking for a roof and LH Rear passenger door by Zeeman
[April 15, 2021, 05:58:27 PM]

clucth cable by druid
[February 08, 2021, 02:04:34 PM]

Sping Setup for CF 1977 Pop Top (Slide Top) by Rich_R
[January 07, 2021, 06:13:08 AM]

Rogue Trooper by greasey monkey
[December 03, 2020, 06:36:00 PM]

Looking for a TK by towman2018
[October 24, 2020, 10:13:01 PM]

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - ben

Pages: [1] 2 3 ... 361
Miscellaneous Technical / Re: Old School Custom?
« on: October 02, 2016, 06:09:33 PM »
in regards to the footroom there are ways around it.

    chev small blocks are narrower so you instantly have more room than other makes

    you can fit the motor offset to the left and have as much room as you want,

   if you sit the motor back a little and as low as possible the rocker covers sit about the same height as the floor and you build the engine cover as part of the floor (i used fibreglass so i had no limits to the shapes i created) so you can still have plenty of room to work on the motor once the engine cover is off but plenty of leg room once engine cover is on, it was hard to get engine cover out so i made it 2 peice cut in the middle side to side.

    you could also move the steering collumn also if you found that easier??

you could do any of these or a combination and have enough room for a left foot.

seriously what cant you do with a beddy!!!


Driveline / Re: power steering
« on: October 02, 2016, 05:56:33 PM »
it seems ve commodore is very straight forward from someone on the site, and ive also had someone say over the phone they used ve rack and it was very easy.


Driveline / Re: Standard front ends
« on: May 07, 2016, 07:19:46 PM »
"Also have found cracking on these plates"

yeh my passenger side bolt almost pulled through on my front end. i thought it was to do with my 350 chev but maybe its another design fault:)


Driveline / Re: My Power Steering Install
« on: April 29, 2016, 07:32:52 PM »
now i think of it someone else i was talking to said the ve rack was a really good option. sounds cool:)

Found for sale / Re: found on ebay
« on: April 22, 2015, 06:18:11 PM »
you wont know good it is untill you look at it. most of the rust looks like surface rust, may be quite a good shell.

Driveline / Re: CL 350 diff ratio
« on: January 25, 2015, 10:04:44 AM »
from memory the cfl duel wheel diffs are either 5.2:1 or 4.2:1  mostly 5.2:1 in my experience.


CF Bedford Chat / Re: K-frame.....drop spindle/axle
« on: January 10, 2015, 06:51:16 PM »

awesome thou.. cheers for that.


CF Bedford Chat / Re: K-frame.....drop spindle/axle
« on: January 10, 2015, 06:34:37 PM »
k frame is the same.

do you have the drop axels already because i have only ever seen 1 set come up once in the last 5 years.

ive herd the same about having to mod the wishbones but dont know.


Driveline / Re: tailshaft mod
« on: January 10, 2015, 06:29:23 PM »
thats alright matte ill have to send my next one to you to get it modded:)


Driveline / Re: tailshaft mod
« on: January 08, 2015, 04:04:58 PM »
Thanks sammy I have been told the hose clamp trick but I didn't know you can keep it loose so it spins into place.

Also been told put the shaft in salt water with the hose clamp on and spin it and balance it that way, apparently the salt water helps it to float.

I think it will be right after talking to a mate who welded ihis up after not using a dial indicator and he said no vibration. Crazy..


Pages: [1] 2 3 ... 361
SimplePortal 2.3.7 © 2008-2021, SimplePortal