User Info
Who's Online
Recent Topics
173 extractors by kylee dingo
[April 07, 2024, 02:55:17 PM]
lowering my bedford cf by Ratbox
[October 07, 2023, 07:59:56 PM]
Sale of 1977 Bedford Motorhome by Anne Speed
[August 26, 2023, 01:04:00 PM]
Adjustable Upper Control Arms by Saville
[August 22, 2023, 11:35:43 AM]
202 red to 202 black Carby engine by johnxb351
[June 21, 2023, 06:33:35 PM]
CF CLUTCH PEDAL by johnxb351
[June 18, 2023, 02:58:15 PM]
Royal Bedford by wendyh
[October 16, 2022, 03:40:43 PM]
Mounting roof consule by greasey monkey
[May 14, 2022, 09:25:38 AM]
Delete my account by wendyh
[May 11, 2022, 07:20:50 PM]
What have you been up to this week by Kenneth71
[May 11, 2022, 04:08:42 PM]
|
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - JOE RYAN
1
« on: June 21, 2016, 05:20:38 PM »
Wire was in the middle connector top right hand corner light blue colour but I gave them all a bit of a clean as most had signs of corrosion
2
« on: June 18, 2016, 09:29:22 AM »
I had a similar problem turned out to be a poor connection in the plug where the wiring harness passed through the firewall on the drivers side up near the top of the inner guard.
I had a multimeter and had 12 V at the indicator light but still would not work the resistance in the connector allowed the voltage to register at nil current but once a bulb tried to illuminate the resistance in the connector prevented sufficient current to pass.
Simple solution was to disconnect the plug and clean/brighten up the pins on the connector and all good
Cheers
Joe
3
« on: March 07, 2015, 09:47:13 PM »
There is one for sale in the Trading Post in Victoria $16,000
4
« on: January 16, 2014, 07:44:19 AM »
Have you tried Rob at Bedford Parts on the South Side of Brisbane 0402989175
5
« on: January 06, 2012, 08:02:29 PM »
Joe Redcliffe
6
« on: December 23, 2011, 04:08:20 PM »
Hey Ben what about your post on the 19th December, or was that just a statement.
Joe
7
« on: December 09, 2011, 05:24:31 PM »
I have a similar plate on my 76 camper that has been welded over the original chassie number on the passenger side firewall, when I asked Qld Transport about it they advised that the stamped original number was difficult to read as the numbers were not stamped in very deep and there was some discussion if a digit was a C or O. So as a solution the Qld Transport issued a new number on a steel plate that they supplied and the owner had to weld on but my number is stamped into the plate not welded like yours.
Cheers
Joe
8
« on: November 20, 2011, 09:43:35 PM »
I have the bottom ones on my 75 SWB
Cheers
Joe
9
« on: November 20, 2011, 09:41:10 PM »
Whats all the white powder is that from a fire extinguisher
Joe
10
« on: October 14, 2011, 10:23:38 PM »
Did you use the manifold off the 186, someone on this site once said the 202 manifold was different to the 186 one, just a idea to consider
Cheers
Joe
|
Guests: 22
Hidden: 0
Users: 0
Show Posts