* User Info

 
 
Welcome, Guest. Please login or register.

* Who's Online

  • Dot Guests: 21
  • Dot Hidden: 0
  • Dot Users: 0

There aren't any users online.

* Recent Topics

For Sale - One Piece Fiberglass Rear Door for CF Van by Rotti
[November 24, 2021, 12:42:56 AM]


Ballast Resistor by pickmeup
[October 19, 2021, 04:25:04 AM]


Door hinge check spring. by wendyh
[October 01, 2021, 10:21:08 PM]


Daily Post by wendyh
[August 31, 2021, 10:28:00 PM]


I am Back!! by wendyh
[June 30, 2021, 08:11:11 AM]


Looking for a roof and LH Rear passenger door by Zeeman
[April 15, 2021, 05:58:27 PM]


clucth cable by druid
[February 08, 2021, 02:04:34 PM]


Sping Setup for CF 1977 Pop Top (Slide Top) by Rich_R
[January 07, 2021, 06:13:08 AM]


Rogue Trooper by greasey monkey
[December 03, 2020, 06:36:00 PM]


Looking for a TK by towman2018
[October 24, 2020, 10:13:01 PM]

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - SkippyThBushKangeroo

Pages: [1] 2 3 ... 83
1
The Sump / Re: MOVIE BEDFORD
« on: January 12, 2015, 08:07:12 PM »
damn was watchin that but decided it was crap after 15 mins so changed channels ..that,ll teach me ay  ;D

2
CF Bedford Chat / Re: DIY wheel alignment
« on: January 12, 2015, 07:59:02 PM »
P.S. i used the method for alighnment that baz suggested to me last year  ;)

3
CF Bedford Chat / Re: DIY wheel alignment
« on: January 12, 2015, 07:57:34 PM »
i thought the springs set the camber which should be zero camber, ( had to do that few weeks ago by cutting springs down , yes was nervous but all panned out ok,.) phew.. and also had to do my own alighnment  which should also i believe be zero toe in or out.... all runs true for me now .. cheers skippy

4
CF Bedford Chat / beddy light switch
« on: January 12, 2015, 07:46:51 PM »
hi groovers.. a question?? is the pull out light switch on a  beddy dash the same format as a holden pull switch ? as have lost low and high beam cept for spotties on high (  had to point the spotties down to get home the other night ) or is there another light switch that can be adapted ??  has been the week for  things to happen ...half km from home yesterday morning took the corner into my road an, bang  ??? snapped a rear wheel axle  :o sigh never a dull moment ay... thanks for any input in advance guys cheers skippy 

5
CF Bedford Chat / Re: tie rod trials
« on: November 07, 2014, 03:31:06 PM »
solved..sent wrong part   :(

6
CF Bedford Chat / tie rod trials
« on: November 07, 2014, 11:42:59 AM »
hey groovers  ordered a new tie rod for 1980 cf, TE476R as i thought was the one, its arrived and its to small ???  does not screw onto tie rod, were there any other part no about have scoured the site but can only come up with that part no. cant remember how i procurred them in adelaide ??? any ideas what this part no is one on right is TE476R one on left is the one that came off front end only thing it has written on it is "trans" & F3.. not really sure whats happened but any advice would be awesome  cheers skippy  :'(  :'(

7
CF Bedford Chat / Re: wheel camber woes
« on: November 04, 2014, 08:47:57 PM »
had that checked an only bit bent was where was shimmed ,.. all else checked out ok i was led to believe..  ::) . scored the lwb front end ,
 in adelaide but on closer inspection  realised it also had copped  :o a belt  :o somewhere down the track, so just used springs out of it ,..    had a wheel align done in adelaide before left for north , asian guy muttered something about "camber".. but i didnt understand him, guess i do now lol ...  see if i can get old ones sent from sa if chop isnt " to my advantage" , just a thought, if they  did go over a tad ,i summise i could space them in the wishbone to regain the camber?? ?? 

8
CF Bedford Chat / Re: wheel camber woes
« on: November 04, 2014, 04:22:39 PM »
what happened re the camber reid??.... sigh  "bedfordus" the god of "all things trying" is not smiling upon me  :-[ things were actually popping off nicely till this ... only a year old ..  noticed both boots were split too ... wish i had these old springs up here with me..  :'(  :'(  :'(

9
CF Bedford Chat / Re: wheel camber woes
« on: November 04, 2014, 11:48:40 AM »
cheers busy.. went to have a chat wiv guy at pedders .. when i said a bedford he did not want a bar of it..  :o "to hard"  :o he said  i said  >:( "your sign behind you says the proffesionals"???   "at what"? i said" pulling yourself n stickin your head in a bucket of sand"??  .. and then he wouldnt talk to me anymore !  ::)  ::) .. i have access to a drop saw but cant really see a way to hold it securly , so was thinking of submerging spring in water an just using a cutting wheel on a grinder?? still very apprehensive of startin the cut though.   :-\   all a part of my libran indecisivness lol ..  ;D

10
CF Bedford Chat / Re: wheel camber woes
« on: November 03, 2014, 08:51:15 PM »
cheers busy  ;) .... ah!!the thickness??? triganometry n physics was never my finer points at school  ::) ::) .. am scared to start with even 5 mm increments ... but  dont want to like.."cut em"  9 times?? pretty sure am venturing into the unresearched n unknown..  :P still pluckin up courage to start" cutting" lol  :-\  :-\

Pages: [1] 2 3 ... 83
anything
SimplePortal 2.3.7 © 2008-2021, SimplePortal