* User Info

 
 
Welcome, Guest. Please login or register.

* Who's Online

  • Dot Guests: 24
  • Dot Hidden: 0
  • Dot Users: 0

There aren't any users online.

* Recent Topics

For Sale - One Piece Fiberglass Rear Door for CF Van by Rotti
[November 24, 2021, 12:42:56 AM]


Ballast Resistor by pickmeup
[October 19, 2021, 04:25:04 AM]


Door hinge check spring. by wendyh
[October 01, 2021, 10:21:08 PM]


Daily Post by wendyh
[August 31, 2021, 10:28:00 PM]


I am Back!! by wendyh
[June 30, 2021, 08:11:11 AM]


Looking for a roof and LH Rear passenger door by Zeeman
[April 15, 2021, 05:58:27 PM]


clucth cable by druid
[February 08, 2021, 02:04:34 PM]


Sping Setup for CF 1977 Pop Top (Slide Top) by Rich_R
[January 07, 2021, 06:13:08 AM]


Rogue Trooper by greasey monkey
[December 03, 2020, 06:36:00 PM]


Looking for a TK by towman2018
[October 24, 2020, 10:13:01 PM]

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bb

Pages: [1] 2
1
Exteriors and Interiors / Re: Holden Dash?
« on: April 17, 2019, 11:36:55 PM »
I've heard the XA falcon dash are quite a good fit, think that includes the XB and XC
Would anyone be kind enough to confirm this? I would like to use a Ford xc dash or landau/LTD dash. Would prefer not to hunt one down and buy it if it's no good for the Bedford CFS

Cheers

2
Driveline / Re: 351 in bedford
« on: January 20, 2017, 01:04:08 AM »
My van has been converted to ford with a donor sub frame and the engine move back a bit. So now it's set-up to forever have a Ford motor. Cool because it's a clevo but I wish I got it with a 308 so I'd have some basic knowledge on it.

My problem is getting someone to identify what the sub frame is(I've got no idea)and then trying to get the van registered later...

3
Driveline / Re: Aluminium fuel tank fabrication in Melbourne?
« on: January 20, 2017, 12:45:36 AM »
Just remember that fuel tanks need engineer approval and you will find it extremely difficult to get an engineer to approve a tank that they didn't see being built.

Does that apply to fuel tanks bought online from parts dealers too? I.e speedmaster?
https://speedmaster79.com/air-fuel-delivery/1-130-014-speedmaster-20-gallon-80-litre-black-aluminium-fuel-cell-wsending-unit/

4
Exteriors and Interiors / Re: Donor Fuel filler housing with door
« on: January 19, 2017, 07:51:41 AM »
That link looks good,  but does that metal part with the flap mean you have to cut and weld that to the outside?

I've got this issue too where I'm starting with a round hole in my drivers side and nothing else.  I've seen a few nice looking fuel caps online,  but normally they don't come with the internal inside flange to position behind the cap

5
Driveline / Re: Collapsible steering column
« on: January 19, 2017, 07:42:42 AM »
Haha batmobile entry style u reckon  :)

Makes me wonder if my seats are in the same position as normal. They are ford xb seats in a custom frame due to the engine being positioned back a little

Another trip to the wreckers to do some measurements I think

6
Driveline / Re: Collapsible steering column
« on: January 18, 2017, 06:18:03 PM »
Hi shagin,

Sounds right about the collapse part.

My column is half way through a custom conversion from the previous owner. At the moment it's a steel lance set-up on the impale angle. This is on a parallel,  flat to chest sport configuration apparently.

From my view it doesn't seem very safe and probably not passable to get rego. I noticed someone else here also had trouble if they weren't using a collapsible column due to their engine upgrade. Mine is also a v8 conversion

Cheers
Brenton

7
Driveline / Collapsible steering column
« on: January 16, 2017, 09:55:10 PM »
Hi all,

This is just a refresh on Dano's original post that's aged a bit now.

I am looking for a collapsible steering column that is minimal in size, something quality that's clean and thin like the classic ratrod type from ididit or flaming river products. Has anyone used any of these on their machine?

I am aware of the cheap import plastic bush tilt columns that break as a side note.

Also I don't know of donor car columns that aren't quite large but I'm open to suggestions.

Cheers
Brenton

8
Introduce Yourself / Re: Sam's SWB Beddy
« on: January 13, 2017, 10:30:40 PM »
No, that's Adelaide for you.

lol that cracks me up because I can tell where the beddy photo was taken too, small world adelaide style

Sam does that workshop(mechanic i think), across the road to your right still have that white beddy still on the road?

9
Introduce Yourself / Re: new owner introduction
« on: March 12, 2015, 11:32:15 PM »
cheers for the replies all

marty- interesting to see you have one of these already. I'll be keen to know if this engine is what I think it is, weekend is the time for some more pics.

Dano-  unfortunately I didn't get to keep the simmons mags, they wanted to sell them at a pretty high price. They were something crazy like 40-50cm wide. I dread to wonder at the tyre prices let alone trying to get that kind of offset registered after going over the pits, they stuck out as far the guard flares on the rear...

wendy/ray - cheers, I think the restoration time was meant to be a slow mission with no corners cut, which has now become my project :)

10
Introduce Yourself / Re: new owner introduction
« on: March 11, 2015, 11:22:19 PM »
gday John,

Cleveland 2V geelong version as far as I'm aware at this stage, im still learning but i'll tag photos with some questions I'm going to post soon. I've got a feeling some of my design issues are going to be solved more through creativity and suggestions from buga members.

Pages: [1] 2
anything
SimplePortal 2.3.7 © 2008-2021, SimplePortal