User Info
Who's Online
Recent Topics
173 extractors by kylee dingo
[April 07, 2024, 02:55:17 PM]
lowering my bedford cf by Ratbox
[October 07, 2023, 07:59:56 PM]
Sale of 1977 Bedford Motorhome by Anne Speed
[August 26, 2023, 01:04:00 PM]
Adjustable Upper Control Arms by Saville
[August 22, 2023, 11:35:43 AM]
202 red to 202 black Carby engine by johnxb351
[June 21, 2023, 06:33:35 PM]
CF CLUTCH PEDAL by johnxb351
[June 18, 2023, 02:58:15 PM]
Royal Bedford by wendyh
[October 16, 2022, 03:40:43 PM]
Mounting roof consule by greasey monkey
[May 14, 2022, 09:25:38 AM]
Delete my account by wendyh
[May 11, 2022, 07:20:50 PM]
What have you been up to this week by Kenneth71
[May 11, 2022, 04:08:42 PM]
|
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - JOE RYAN
71
« on: February 20, 2009, 07:29:02 PM »
Guy's
If you are referring to the bushers on the rods connected to the back of the front cross member and going towards the rear and connecting to the chassic (not really castor Rods) I bought a full set from Pedders Suspension at Stafford in Brisbane about 12 months ago for about $120 off the shelf,they had the listing on their books
Joe
72
« on: February 05, 2009, 09:19:34 PM »
Dano
The two tanks that were in my camper had a seperate gauge on each with a fuel line from each tank connected to a changeover manual valve mounted under the floor with just the handle poking into the cabin on the floor near the handbrake. I took the extra tank out as I put the van on gas and need the space under floor. I have the tank up the back yard and most likely the valve in the shed you can have for $0 if you want them just pay for postage I'm in Brisbane
Joe
73
« on: January 02, 2009, 01:40:45 PM »
I have a SWB 78 camper fitted out with cupboards, water tanks etc on gas and petrol, 186 with trimatic and 3.55 HZ diff OK around town but a bit sluggish on the hwy. At 100 klm 3000 revs, 60klm 2000 rpm when the van was a manual revs about 400 less at 100 klm. I have a 2.78 to try out but I am concerned that it will be too tall around town
Joe
74
« on: December 19, 2008, 09:40:09 AM »
Dave
I have a good one but I'm in Brisbane
Joe
75
« on: November 25, 2008, 04:16:21 PM »
Ben
Did you end up selling the sun visior if not pm on 0418721605
Joe
76
« on: November 19, 2008, 01:00:25 PM »
Thanks Hotrod
One other point is the door down or rolled up when I do this tensioning
Joe
77
« on: November 19, 2008, 10:33:20 AM »
:-[Has oneone cut down a used garage roller door and installed it, is there a trick to tensioning the spring mechanism inside the door and do you need any specialised tool. I have heard plenty of horror stories, I want to replace thr lintel in my shed so that I can remove the two single door and replace with one double roller door
Thanks
Joe
78
« on: October 31, 2008, 06:20:24 PM »
I changed my 77 SWB from 3 speed manual to TRIMATIC and the same gearbox mount and cross member was used the manual and trimatic are the same length with the same driveshaft yoke spline
79
« on: September 14, 2008, 07:25:07 PM »
I am up for a get together but I will be in WA on holidays until the 22 Oct which is a shame as I live about 400m from Pelican park see you at the next get together
Joe
80
« on: August 03, 2008, 03:38:22 PM »
Shane J and any other Brisbane members
I am at Redcliffe contact on janddryan1@optusnet.com.au with phone number so we can meet up organise a get together with other Brisbane members
|
Guests: 30
Hidden: 0
Users: 0
Show Posts